[IDV #NVG-651398]: Donut hole poleward of 30N

> I tried ozone, zonal wind, temperature, different levels, etc.
> It has nothing to do with the vaues or range or units.
> It is the projection and rendering of color shaded plan views around the pole.

I think this is the same problem you showed me in the training workshop last 
year. Need to reset the transparency.


Yuan
> Do you see the images I attach to emails?
> 
> On Oct 23, 2013, at 5:04 PM, Unidata IDV Support wrote:
> 
> >> Any variable.
> >> I used air temperature at the 200mb level.
> >> Same for a wind component at 400mb level.
> >
> >
> > I tried air temp at the 200mb, not seeing this problem. In general, you can 
> > check the parameter default range under Tools > Parameter Default Editor, 
> > and make the adjustment there.
> >
> >
> >
> > Yuan
> >>
> >>
> >>
> >> On Oct 23, 2013, at 3:25 PM, Unidata IDV Support wrote:
> >>
> >>>> That loads OK, as the original did.
> >>>>
> >>>>
> >>>> I load it. Good.
> >>>> I try to create a color-shaded plan view of T200.
> >>>
> >>> What is T200? I didn't see this variable.
> >>>
> >>>
> >>> Yuan
> >>>> It causes a reprojection to lat-lon square.
> >>>> When I reproject under Projections-> North Pole, I get the donut hole 
> >>>> with the dateline gap:
> >>>>
> >>>> [cid:6cadcb07-9070-4040-9853-4c0e2cfcc7b3@amazon.rsmas.miami.edu]
> >>>>
> >>>>
> >>>> ---------
> >>>> Second try:
> >>>> I load your test bundle, uncheck "Auto-set projection", then create T200 
> >>>> .
> >>>> Now I get the donut hole directly and imeediately.
> >>>>
> >>>>
> >>>>
> >>>>
> >>>>
> >>>>
> >>>>
> >>>>
> >>>> On Oct 23, 2013, at 1:13 PM, Unidata IDV Support wrote:
> >>>>
> >>>>>> Perhaps you misunderstood the question.
> >>>>>>
> >>>>>> The support form state capture is the problem: it is my attempt to 
> >>>>>> remake my old bundle with polar displays, this time using the time 
> >>>>>> driver. It has basic display problems on the polar projection.
> >>>>>>
> >>>>>>
> >>>>>> Yes i know how to use the time driver. The old bundle on ramadda works 
> >>>>>> fine, but it did not use the time driver. I made it during training in 
> >>>>>> 2012 with specific times.
> >>>>>>
> >>>>>>
> >>>>>> Brian Mapes
> >>>>>
> >>>>> Brian,
> >>>>>   I downloaded your old bundle and then set the time driver,  and saved 
> >>>>> a new bundle. See the attached.
> >>>>>
> >>>>>
> >>>>>
> >>>>> Yuan
> >>>
> >>>
> >>> Ticket Details
> >>> ===================
> >>> Ticket ID: NVG-651398
> >>> Department: Support IDV
> >>> Priority: Normal
> >>> Status: Open
> >>>
> >>
> >> Brian Mapes
> >> address@hidden or address@hidden
> >>
> >>
> >>
> >>
> >
> >
> > Ticket Details
> > ===================
> > Ticket ID: NVG-651398
> > Department: Support IDV
> > Priority: Normal
> > Status: Open
> >
> 
> Brian Mapes
> address@hidden or address@hidden
> 
> 
> 
> 


Ticket Details
===================
Ticket ID: NVG-651398
Department: Support IDV
Priority: Normal
Status: Open