> Nope, unchecking all other displays still shows the C. > I do View->Bring to front all the time with transparent layers, I am highly > aware of that. > > But it's true the donut surrounds the wireframe box, which may be a clue. > Try the attached bundle. Yuan > > On Oct 23, 2013, at 5:27 PM, Unidata IDV Support wrote: > > >> I tried ozone, zonal wind, temperature, different levels, etc. > >> It has nothing to do with the vaues or range or units. > >> It is the projection and rendering of color shaded plan views around the > >> pole. > > > > I think this is the same problem you showed me in the training workshop > > last year. Need to reset the transparency. > > > > > > Yuan > >> Do you see the images I attach to emails? > >> > >> On Oct 23, 2013, at 5:04 PM, Unidata IDV Support wrote: > >> > >>>> Any variable. > >>>> I used air temperature at the 200mb level. > >>>> Same for a wind component at 400mb level. > >>> > >>> > >>> I tried air temp at the 200mb, not seeing this problem. In general, you > >>> can check the parameter default range under Tools > Parameter Default > >>> Editor, and make the adjustment there. > >>> > >>> > >>> > >>> Yuan > >>>> > >>>> > >>>> > >>>> On Oct 23, 2013, at 3:25 PM, Unidata IDV Support wrote: > >>>> > >>>>>> That loads OK, as the original did. > >>>>>> > >>>>>> > >>>>>> I load it. Good. > >>>>>> I try to create a color-shaded plan view of T200. > >>>>> > >>>>> What is T200? I didn't see this variable. > >>>>> > >>>>> > >>>>> Yuan > >>>>>> It causes a reprojection to lat-lon square. > >>>>>> When I reproject under Projections-> North Pole, I get the donut hole > >>>>>> with the dateline gap: > >>>>>> > >>>>>> [cid:6cadcb07-9070-4040-9853-4c0e2cfcc7b3@amazon.rsmas.miami.edu] > >>>>>> > >>>>>> > >>>>>> --------- > >>>>>> Second try: > >>>>>> I load your test bundle, uncheck "Auto-set projection", then create > >>>>>> T200 . > >>>>>> Now I get the donut hole directly and imeediately. > >>>>>> > >>>>>> > >>>>>> > >>>>>> > >>>>>> > >>>>>> > >>>>>> > >>>>>> > >>>>>> On Oct 23, 2013, at 1:13 PM, Unidata IDV Support wrote: > >>>>>> > >>>>>>>> Perhaps you misunderstood the question. > >>>>>>>> > >>>>>>>> The support form state capture is the problem: it is my attempt to > >>>>>>>> remake my old bundle with polar displays, this time using the time > >>>>>>>> driver. It has basic display problems on the polar projection. > >>>>>>>> > >>>>>>>> > >>>>>>>> Yes i know how to use the time driver. The old bundle on ramadda > >>>>>>>> works fine, but it did not use the time driver. I made it during > >>>>>>>> training in 2012 with specific times. > >>>>>>>> > >>>>>>>> > >>>>>>>> Brian Mapes > >>>>>>> > >>>>>>> Brian, > >>>>>>> I downloaded your old bundle and then set the time driver, and > >>>>>>> saved a new bundle. See the attached. > >>>>>>> > >>>>>>> > >>>>>>> > >>>>>>> Yuan > >>>>> > >>>>> > >>>>> Ticket Details > >>>>> =================== > >>>>> Ticket ID: NVG-651398 > >>>>> Department: Support IDV > >>>>> Priority: Normal > >>>>> Status: Open > >>>>> > >>>> > >>>> Brian Mapes > >>>> address@hidden or address@hidden > >>>> > >>>> > >>>> > >>>> > >>> > >>> > >>> Ticket Details > >>> =================== > >>> Ticket ID: NVG-651398 > >>> Department: Support IDV > >>> Priority: Normal > >>> Status: Open > >>> > >> > >> Brian Mapes > >> address@hidden or address@hidden > >> > >> > >> > >> > > > > > > Ticket Details > > =================== > > Ticket ID: NVG-651398 > > Department: Support IDV > > Priority: Normal > > Status: Open > > > > Brian Mapes > address@hidden or address@hidden > > > > Ticket Details =================== Ticket ID: NVG-651398 Department: Support IDV Priority: Normal Status: Open
Attachment:
test-2.xidv
Description: Binary data