RE: LDM - HU

also in work2/russell/bin/perl

go ahead and configure whichever version appears more complete..

Then run scriptconfig again and let me know how it goes..


Thanks,

-Jeff
____________________________                  _____________________
Jeff Weber                                    address@hidden
Unidata Support                               PH:303-497-8676 
NWS-COMET Case Study Library                  FX:303-497-8690
University Corp for Atmospheric Research      3300 Mitchell Ln
http://www.unidata.ucar.edu/staff/jweber      Boulder,Co 80307-3000
________________________________________      ______________________

On Tue, 21 May 2002, Byles, Pavel O wrote:

> I found it
> 
> /meiyu/opt
> 
> Pavel Byles
> 
> -----Original Message-----
> From: Jeff Weber
> To: Byles, Pavel O
> Cc: ldm-support
> Sent: 5/21/02 11:41 AM
> Subject: RE: LDM - HU
> 
> I have added the runtime link to the version:
> Change the runtime link
> 
> For a new LDM installation: 
> 
>     Install the runtime link 
> 
>            % cd ~ldm
>            % ln -s {version-directory} runtime
> 
> Now if I can just find  where perl is living..
> 
> -Jeff
> ____________________________                  _____________________
> Jeff Weber                                    address@hidden
> Unidata Support                               PH:303-497-8676 
> NWS-COMET Case Study Library                  FX:303-497-8690
> University Corp for Atmospheric Research      3300 Mitchell Ln
> http://www.unidata.ucar.edu/staff/jweber      Boulder,Co 80307-3000
> ________________________________________      ______________________
> 
> On Tue, 21 May 2002, Byles, Pavel O wrote:
> 
> > thanx
> > 
> > Pavel Byles
> > 
> > -----Original Message-----
> > From: Jeff Weber
> > To: Byles, Pavel O
> > Cc: ldm-support
> > Sent: 5/21/02 10:55 AM
> > Subject: RE: LDM - HU
> > 
> > Hi Pavel, 
> > 
> > scriptconfig is looking for perl and cannot find it...
> > 
> > place the path to perl in ldm's .cshrc file.
> > 
> > If I remember corrrectly it was /space/russell/...something..
> > 
> > I'll poke around a bit..
> > 
> > -Jeff
> > ____________________________                  _____________________
> > Jeff Weber                                    address@hidden
> > Unidata Support                               PH:303-497-8676 
> > NWS-COMET Case Study Library                  FX:303-497-8690
> > University Corp for Atmospheric Research      3300 Mitchell Ln
> > http://www.unidata.ucar.edu/staff/jweber      Boulder,Co 80307-3000
> > ________________________________________      ______________________
> > 
> > On Tue, 21 May 2002, Byles, Pavel O wrote:
> > 
> > > Sorry let me ammend that last message: I set the hostname and the
> > $HOME
> > > path. I now get this:
> > > 
> > > Check that the following defines are correct:
> > > 
> > > ./scriptconfig: no: not found
> > > perl is located at: no perl in . /bin /usr/bin /usr/ucb /etc
> > > /space/home/ldm/decoders /space/home/ldm/util /space/home/ldm/bin
> > > /space/home/ldm/man
> > > 
> > > $LDMHOME  is defined as /space/home/ldm
> > > 
> > > fully qualified $HOST is defined as zephyr.atmphys.howard.edu
> > > 
> > > If these defines are not correct, edit file scriptconfig to manually
> > set
> > > the required variables.
> > > 
> > > ldmadmin was configured
> > > ldmcheck was configured
> > > ldmfail was configured
> > > ldmprods was configured
> > > mailpqstats was configured
> > > netcheck was configured
> > > syscheck was configured
> > > 
> > > Pavel Byles
> > > 
> > 
> > 
>