Re: 20010920: nsharp printing pblms

Hi Steve,
We installed the 5.6.C and still no luck.  Do you recall who else had this 
problem on
Solaris.  I could maybe contact them and see if they figured this out.  I have 
a power user
here (finally using gempak) and I'd like to keep them happy!.

As always, best regards, Glenn

Unidata Support wrote:

> You have a binary distribution. The binary distributions contain
> the executables and tables necessary for running the programs.
> The tarfiles do not contain GEMPAK source or configuration directories
> since they are only used to build the distribution.
>
> To build the distribution, you would have to have the source distribution.
>
> The nsharp patch on the web site is included in 5.6.C and higher so there
> is nothing to use there.
>
> The most likely cause of pop-up widget problems is that openwindows (Solaris)
> has a problem and/or requires a patch. I do not have a solution at this time 
> since it
> works on our systems here. But, I do know of at least one other site that has 
> the problem
> under solaris and will try to find time to look at the problem at some point.
>
> Steve Chiswell
> Unidata User Support
>
> >From: "Glenn Rutledge" <address@hidden>
> >Organization: UCAR/Unidata
> >Keywords: 200109201258.f8KCwv123517
>
> >This is a multi-part message in MIME format.
> >--------------62028B7D600943542EDFE0A3
> >Content-Type: text/plain; charset=us-ascii
> >Content-Transfer-Encoding: 7bit
> >
> >I'm still trying to figure out why I don't get an nsharp popup to print
> >(it just crashes) I noticed in my Gemenviron
> ># CONFIGURATION directory
> >   setenv CONFIGDIR $NAWIPS/config
> >#
> >no "config" directory exists for that.  The only config is in the garp
> >subdirectory.  THis is true in the older 5.6 version that is running
> >(still w/o the nsharp print capability).  Why is this?  Is it needed or
> >set somewhere else?
> >
> >Also, when I try to make the nsharp patch I cannot make.  It can't find
> >the makeinc.common.  (that's in the garp config).  So, I copied that
> >over to a new config directory under $NAWIPS, and it still can't make
> >target.
> >
> >Perplexed.   Glenn
> >
> >--------------62028B7D600943542EDFE0A3
> >Content-Type: text/x-vcard; charset=us-ascii;
> > name="Glenn.Rutledge.vcf"
> >Content-Transfer-Encoding: 7bit
> >Content-Description: Card for Glenn.Rutledge
> >Content-Disposition: attachment;
> > filename="Glenn.Rutledge.vcf"
> >
> >begin:vcard
> >n:;Glenn K. Rutledge
> >x-mozilla-html:FALSE
> >org:National Climatic Data Center;Climate Data Division
> >adr:;;;;;;
> >version:2.1
> >email;internet:address@hidden
> >title:Meteorologist
> >fn:Glenn K. Rutledge
> >end:vcard
> >
> >--------------62028B7D600943542EDFE0A3--
> >
>
> **************************************************************************** <
> Unidata User Support                                    UCAR Unidata Program <
> (303)497-8644                                                  P.O. Box 3000 <
> address@hidden                                   Boulder, CO 80307 <
> ---------------------------------------------------------------------------- <
> Unidata WWW Service                        http://www.unidata.ucar.edu/      <
> **************************************************************************** <

begin:vcard 
n:;Glenn K. Rutledge
x-mozilla-html:FALSE
org:National Climatic Data Center;Climate Data Division
adr:;;;;;;
version:2.1
email;internet:address@hidden
title:Meteorologist
fn:Glenn K. Rutledge
end:vcard